Journal of Zhejiang University SCIENCE A
(Monthly)

2006   Vol. 7   No. 11   p. 1846-1855

Field investigation on effects of railway track geometric parameters on rail wear

SADEGHI J.^†, AKBARI B.

(School of Railway Engineering, Iran University of Science and Technology, Narmak, Tehran, Iran)
^†E-mail: Javad_sadeghi@iust.ac.ir
Received Oct. 20, 2005 revision accepted July 25, 2006

Abstract: Rail wear has dramatic impact on track performance, ride quality and maintenance costs. The amount of rail wear is influenced by various elements among which geometric parameters play an important role. The amount of wear in Iran’s railway lines and its imposed maintenance costs oblige us to make modifications on the various geometrical parameters. In order to ensure the effectiveness of these changes, it is necessary to investigate these parameters and their effects on the wear. This research is aimed at studying the effects of different track geometrical parameters on the vertical and lateral wear by conducting a three phase field investigation. The first phase was carried out at the switches of a station, the second phase at a straight line, and the third at a curved line out of the station. The results obtained are analyzed and the role of each track geometrical parameter in the rail wear is discussed. Recommendations for prevention or reduction of rail wear are presented.

Key words: Rail wear, Vertical and lateral wear, Superelevation, Gauge, Longitudinal slope, Track geometry
doi:10.1631/jzus.2006.A1846             CLC number: TU375

References:

[1] Allery, B.P., 1993. Improvements in rail maintenance techniques and manufacturing processes. Proc. Instn. Civ. Engrs. Transp., 100:227-230.

[2] Csontos, I., 1989. A Solution to Excessive Wear on Turnouts Caused by Long, Heavy Axle-Load Trains. IHHA 4th Conference, p.34-41.

[3] Dearden, J., 1960. The wear of steel rails and tyres in railway service. Wear, 3(1):43-59.

[4] Esveld, C., 2001. Modern Railway Track (Second Ed.). Delft University of Technology Pub Service, p.17-55.

[5] Gahr, K.H.Z., 1987. Microstructure and Wear of Materials. Tribology Series 10, Elsevier, Amsterdam-New York.

[6] Iran Ministry of Roads and Transportation, 2004. General Technical Specifications of Iranian Railway Superstructure. Deputy of Training and Research Pub Co., p.37-44 (in Persian).

[7] Kramp, K.P., 1998. The Analysis and Creation of Track Irregularities Using TRAKVU. Master Thesis, Virginia Polytechnic Institute, Blacksburg Virginia, p.10-15.

[8] Mutton, P.J., Marich, S., 1981. Rail Requirements for Heavy Haul Rail Systems. Proceedings of the 34th Australian Institute of Metals Annual Conference, p.5-10.

[9] Mutton, P.J., Epp, C.J., 1983. Factors Influencing Rail and Wheel Wear. Proceedings of Railway Engineering Symposium, IEAust, Melbourne, p.216-221.

[10] Profillidis, V.A., 2000. Railway Engineering (Second Ed.). Ashgate Pub Co., p.207-233.

[11] Sadeghi, J., 2002. Sufficient Experimental Methods in Investigation of Dynamic Behavior of Track Components and Track System. Proceeding of the 7th International Conference on Mechanics of Systems, University of Wollongong, Australia, p.71-79.

[12] Sadeghi, J., 2004. Investigation on Wheel/Rail Wear in Iranian Railway Lines. Proceeding of the 6th International Conference on Civil Engineering, Isfahan University of Technology, p.171-180 (in Persian).

[13] Spikes, H.V., Olver, A.V., Macpherson, P.B., 1986. Wear in rolling contacts. Wear, 112(2):121-144.